Can you paint over glazing putty? Painting must be done only after firm set is achieved. To soften the glazing putty, you can pop it in the microwave for 20 seconds set it on full and open the top of the tub. You should only do this is the glazing putty is in a plastic tub. Alternatively, you can mix in a little linseed oil which will soften the glazing putty. Be careful not to use too much. If your going to use Linseed oil putty then you can paint this straight away as the oil in the putty will want to come out as it dries for some days after.
If you are using glazing putty in a warm, dry environment, this trick can cut your wait time in half. For shorter glazing putty drying time in Denver, CO, choose latex glazing putty instead of oil-based. To soften any hard putty you can use a heat gun.
Heating the putty up will cause it to go soft and make removing it much easier. Run the heat gun over the putty from side to side, being careful not to concentrate any heat in one spot for too long as if glass gets too hot it will crack. We probably waited weeks before painting. I guess it is ready to paint. The putty on the window I did yesterday is sticky, whereas I can run my fingers over the 2 week old putty. POLL: How long does it take to choose a paint color? How long does hardwood need to acclimate in the house b4 setting?
Yay or nay? Subway tile backsplash in putty. Once it "skins" over it is ready to paint, usually a day or 2. If I have more than a single window I usually build a quick 'hot box' using a W incandescent bulb for heat and some heavy plastic. I'm just starting to reglaze my house windows.
I'm using '33 but same question stream-- should I re hang the sash I puttied while it dries enough to paint? I've got a storm, so it's optional right now, but I've got MANY windows to do and can't imagine waiting days to finally paint?? Also, are there any other brands people like in particular? I heard one bad thing about '33, but that's about it. I invariably prime the entire sash before replacing the glass, so I have no need to prime again before the finish paint, which is gloss oil, The putty doesn't need priming when it has skinned.
Although I have never used it, I understand that Sarco putty beats the Dap 33 product in drying time, and I hope consistency. I always have to do something to a quart or gallon of the Dap product to get it fit for use, It's either too runny or too dry. Here is a link that might be useful: Putty Analysis. It can't hinder the drying; but it won't accelerate it a great amount.
I kept newly-glazed wood sash in the back of my pickup under the truck cap in the sun for a week to get the putty to speed set. Days it would hit in there. Have you ever tried a wood moisture meter to monitor your progress?
I have no experience with these devices. A moisture meter will not tell you anything useful about the putty hardening, the goal of the process. I should have made it clear that I wondered if you had used a moisture meter to monitor the wood itself before repainting.
I've been reglazing the windows on the front of my house this week with dap I did the first window about 10 days ago, and it has set up enough to paint now. I'll be back at it. I really like it. Have any of you tried Glaze-Ease , which can be painted in two hours, and is applied with a caulking gun? Here is a link that might be useful: Glaze-Ease Not used Glaze-Ease, but it would seem to me that applying with a caulking gun requires an extremely steady hand with it being difficult to control Keep in mind that the glazing putty will not be cured yet if you dry it with this method, but the exterior will be dry enough to paint.
If you plan to do a lot of windows, a steam box is absolutely the way to go. For one or two windows, the chisel and scraper is the best. After an hour in the steamer, the glazing putty is softened up and comes off much easier. One or two layers of wall putty are ideal. However, the right drying time Minimum hrs. After the second coat of putty, it is desirable to leave the surface to dry, preferably overnight. Latex glazing does not need to be painted, but unless your windows are white, you will want to paint the glazing to match the color.
Typically, the glazing is dry and stiff enough to paint after three to seven days, depending on the weather. You can paint right over it without spreading primer paint first. If you are using glazing putty in a warm, dry environment, this trick can cut your wait time in half. Simply mix the drying compound with the glazing putty and apply the putty as you normally would.
The product is designed to speed up the drying process without affecting the quality of the putty. You can find this product in most hardware stores. For shorter glazing putty drying time in Denver, CO, choose latex glazing putty instead of oil-based. The latex variety is water-based. Because of the water base, the latex version can cure faster.
0コメント